Topcoat 2L/67oz 3.0kg/6.6lbs (1K) Clear Textured

SI35 is an incredibly tough, 1-component surface coating with infused micronized nanoparticles which forms a durable matrix of molecular bonds (transformation into a carbon shield) resulting in permanent protection and and in a smooth non slip surface.

The coating can be applied directly and without primer to concrete, steel, wood, acrylic, plaster, painted or unpainted surfaces, indoors or outdoors.

Reachable area 

• 3 layers +/- 315gr/m2 - 225ml/m2 75 micron =   6m2

• 2 layers +/- 210gr/m2 - 150ml/m2 50 micron =   9m2

• 1 layer   +/- 105gr/m2 -   75ml/m2 25 micron = 18m2

• 3 layers 0.06lbs/ft2 - 0.96oz/ ft2 = 3 mil/  60ft2  

• 2 layers 0.04lbs/ft2 - 0.64oz/ ft2 = 2 mil/  90ft2  

• 1 layer   0.02lbs/ft2 - 0.32oz/ ft2 = 1 mil/180ft2

Advantages

• Three simple steps: Clean, Dry, and Apply.

• Easily repels water, dirt, dust, and pollutants.

• This coating has an outstanding hydrophobic effect.

• Restores damaged finishes and reduces cleaning intervals.

• Resistant to all kinds of chemicals and UV radiation.

• Anti Termite

• Superior anti-pollution and anti-corrosion properties.

• This coating can withstand temperatures of 300°C / 600°C

• Suitable for making walls fire retardant and is most best solution to make rooftops waterproof

Technical Specifications

• Thickness: 1 layer 1mil / 25 micron (Air Spray)

• Hydrophobic 

• Zero Absorption permeability

• Hardness H9 

• Thermal Change -Thermal shock Compatible

• UV- Atmospheric agents - Anti-Aging Proof

• Temperature resistent 300°C / 600°F

• Severe Chemical Attack resistant Liquids Group1 EN13529

• Impact resistance 1kg from 62,5cm Height / 2.2lbs from 25inch

• Adhesion strength by pull-off: 2.4-2.6 N/mm2

Application information / How to use

Ambient temperature: 5-30°C / 41-86°F Avoid direct sunlight and/or high humidity.

IMPORTANT

Wear a full-face chemical respirator mask, safety suit and latex or nitrile gloves

Application information

The SI35 coating can be applied directly or indirectly on all surfaces (porous and non-porous) such as concrete, steel, wood, acrylic, gypsum, painted or unpainted surfaces, indoors, or outdoors. The surface underneath will be superbly protected against erosion and corrosion and will stay cleaner longer. Cleaning becomes quicker, easier, and less expensive, as special cleaning agents are unnecessary.

Preparation

Make sure the surface is free from any contamination and dirt. A zinc rich primer can be used in case of problems with the substrate. Warning the surface must be completely dry before application and must stay dry for 6 hours after application after application!

This is a 1-Component Air Cure System

Spray in thin layers until the surface reaches a thickness of 3 mil / 75 micron after drying. Depending on the surface, material and structure, different application techniques can be used, such as a paint sprayer or brush.

Let the surface dry for 24 hours. It is touch-dry in 1 hours, after 4 hours, 85% cured, and the remaining 15% (transformation into a carbon shield) is fully cured after 7 days. Be aware that the mixed contents cannot be stored longer than 3 hours. The surface can simply be maintained with a high pressure washer at 80 bar using our biologically degradable Reactivating Shampoo.

Tool cleaning

The individual components, as well as the mixing system of the paint sprayer, can be diluted and cleaned using our Steril Cleaner.

Storage and handling

Packaging Information

Includes plastic sealed wrap

1 pcs single 3.4kg/7.5lbs measurement L17cm x W13cm x H12cm / L7inch x W5inch x H5inch

8 pcs in a carton W52cm x H15cm x D44cm / W20.5inch x H5.9inch x D17.3inch  27.3kg/60lbs